 |
|
| |
 |
| FAIRCHILD |
| FUJI |
| MITSUBISHI |
| TOSHIBA |
| SEMIKRON |
| EUPEC |
| WESTCOND |
|
|
| |
 |
| FUJI |
| MITSUBISHI |
| SANREX |
| EUPEC |
| ABB |
|
|
| |
 |
| SANREX |
| IXYS |
| EUPEC |
| MITSUBISHI |
| WESTCODE |
| SEMIKRON |
| URC |
| ABB |
|
|
| |
 |
| EUPEC |
| FUJI |
| IXYS |
| MITSUBISHI |
| SANREX |
| SEMIKRON |
| URC |
| WESTCODE |
| ABB |
|
|
| |
 |
| BCC |
| NICHICON |
| HITACHI |
| NCC |
| ITELCOND |
| JICON |
|
|
| |
 |
| JEAM MALLIE |
| FERRAZ |
| BUSSMAM |
|
|
| |
 |
|
| |
 |
|
| |
 |
|
|
 |
|
|
 |
|
 |
|
|
 |
SEMIKRON |
|
|
SKiiP￠c2,3 l 600v |
|
|
| |
| Summary of
standard 600V-SKiiP®2,3 |
| Type |
Circuit |
VCES/ V |
IC/ A5
|
IRMS1
|
IRMS2
|
Options3
|
Case |
Interface |
| SKiiP®2 - standard types
with NPT-IGBT and freewheeling
CAL-Diode® |
| 202 GD 061-359 CTV |
6-pack |
600 |
200 |
146 |
104 |
U,L,W |
S3 |
GD |
| 302 GD 061-359 CTV |
6-pack |
600 |
300 |
188 |
137 |
U,L,W |
S3 |
GD |
| 402 GD 061-358 CTV |
6-pack |
600 |
400 |
2007) |
178 |
U,L,W |
S3 |
GD |
| 802 GB 061-259 CTV |
2-pack |
600 |
800 |
4007) |
383 |
U,F,L,W |
S2 |
GB |
| 1602 GB 061-459 CTV |
2-pack |
600 |
1600 |
8007) |
665 |
U,F,L,W |
S4 |
GB
|
|
| |
| SKiiP®3 Standard types
(preliminary) |
| Type |
Circuit |
VCES/ V |
IC/ A5
|
Options3
|
Case |
Interface |
| 613 GD 061-3DU |
6-pack |
600 |
600 |
L,W |
S33 |
GD |
| 803 GD 061-3DU |
6-pack |
600 |
800 |
L,W |
S33 |
GD
|
|
|
|
|
Non standard types on
request. Please find latest information on
internet page http://www.semikron.com/ or
contact your local SEMIKRON -
representative. For electrical and thermal
design support please use SEMISEL. Access
to SEMISEL is
via SEMIKRON website http://semisel.semikron.com/.
Further questions can be placed on internet
page http://faq.semikron.com/.
|
| Features
|
- Low thermal impedance
- Optimal thermal management with integrated
heatsink
- Pressure contact technology with increased
power cycling capability
- Compact design
- Low stray inductance
- High power, small losses
- Fast and soft recovery CAL diode
- Recycable
- Integrated current sensors
- Integrated driver with
- Overtemperature protection
- Overcurrent protection due to current
sensors
- Overvoltage protection (DC-link) (-option-)
- Built-in dead time and interlock
- CMOS compatible inputs
- Fiber optic connector (option for
halfbridges)
|
| Typical
Applications |
- Half, Fullbridges and H-bridges
- Three phase motor drive inverter
- Uninterruptable power supplies UPS
- Converter
- General power switching supplies
- Inductive heating
- DC Chopper
|
1. Output
rms-phase-current with typical operating
conditions as shown in table below, SKiiP 2
mounted on P16 heat sink with standard fan
SKF16B-230-01
| VCES/V |
VV/V |
VD/V |
cos phi |
fsw/kHz |
fout/Hz |
Tjmax/°C
|
Ta/°C
|
| 600 |
230 |
320 |
0.8 |
5 |
50 |
125 |
40
|
|
|
2. Output
rms-phase-current with operating conditions as
above but 150% overload capability for 60s and
fout=2Hz - 50 Hz |
3. Available options:
| U: DC-link voltage sense and
over-voltage protection |
| F: Fiber optic connector
|
| E: brake chopper voltage
levels for 400V mains voltage (for 1200V-SKiiP
only) |
| A: brake chopper voltage
levels for 460V mains voltage (for 1200V-SKiiP
only) |
| L: SKiiP?/SUP>2,3
mounted on P16 (SKiiP?/SUP>3: PX16
except SKiiP?/SUP>313GD122-3DUL,
SKiiP?/SUP>413GD061-3DUL) heat sink for
air cooling |
| W: SKiiP 2,3 mounted on NWK40
heat sink for liquid cooling
|
|
| 5. Current per
switch @ 25 °C heat sink temperature
temperature |
| 6. This type has two gate
drivers; when Option "U" is ordered only one
gate driver is equipped with Option "U"
|
| 7. Maximum continuous current
is limited by current sensor capability
|
|
|
|
|
 |
| |
|
|
|
